Quote:
Should I run two dipsticks (Shut up Sandy & 'Zilla!
)Wonder where this is going.....
| Slant Six Forum https://www.slantsix.org/forum/ |
|
| Rob's 1981 Dodge Challenger https://www.slantsix.org/forum/viewtopic.php?t=46322 |
Page 11 of 61 |
| Author: | wvenable [ Sat Jul 06, 2013 11:32 am ] |
| Post subject: | |
Quote: Should I run two dipsticks (Shut up Sandy & 'Zilla! )Wonder where this is going.....
|
|
| Author: | sandy in BC [ Sat Jul 06, 2013 11:56 am ] |
| Post subject: | |
.....already gone........ ( . )( ' ) |
|
| Author: | Rob Simmons [ Sat Jul 06, 2013 9:05 pm ] |
| Post subject: | |
I pulled the head off the K1/Wiseco engine today so I can put the Howard Davis head on it. I got everything cleaned up and ready to re-install, but want to check measurements just to make sure I'm on the right track. Head gasket is .042 copper Pistons are out of the hole .011 on the intake side .012 on the distributor side Combustion chamber is 48 cc Valves are 1.45 and 1.70 Bore is 3.504 I'll be using RAS 1.5 roller rockers Cam is 290 @ 20, .597 lift, 104 centerline, 263 duration @ 50 Now,... Where is that old Auto Math Handbook I had around here...? I don't think I will have any valve to piston or bore side interference issues. 3.504 is bigger bore than Howard was running and the 1.45 / 1.70 valves are smaller than the 1.4? / 1.78 valves in the Bruner head I just took off... I don't know the chamber volume on the Bruner head though... It's midnight... Too late to think too hard... (Yeah, yeah... Go ahead! You know you want to...  )Goodnight! 
|
|
| Author: | slantzilla [ Sat Jul 06, 2013 11:05 pm ] |
| Post subject: | |
Say goodnight Gracie.
|
|
| Author: | Rob Simmons [ Sun Jul 07, 2013 6:35 am ] |
| Post subject: | |
You so funny! I think I'll rig up something to CC the combustion chambers on the various heads I have laying around so I can compare them. The 48 cc figure is one from Howard's notes, but I haven't confirmed it. Don't know about the Bruner head. I have flow data, but can't seem to find the chamber volume figure for the Foster head. And then I've got another head that is said to have been milled about .050 that I'd like to verify. I'd like to button the race engine back up today or tomorrow, but want to make sure on the chamber volume first. I'm off to the garage... |
|
| Author: | slantzilla [ Sun Jul 07, 2013 8:22 am ] |
| Post subject: | |
Has Poser boy showed up yet?
|
|
| Author: | sandy in BC [ Sun Jul 07, 2013 9:18 am ] |
| Post subject: | |
No....... Im busy all day. |
|
| Author: | slantzilla [ Sun Jul 07, 2013 9:50 am ] |
| Post subject: | |
No, the OTHER Poser boy.
|
|
| Author: | wvenable [ Sun Jul 07, 2013 4:10 pm ] |
| Post subject: | That's Mr. Poser Boy.... |
http://www.youtube.com/watch?v=Qw9oX-kZ_9k |
|
| Author: | Rob Simmons [ Sun Jul 07, 2013 8:12 pm ] |
| Post subject: | |
Yep, he showed up & we hung out fer awhile.  We swapped a few parts around & I even introduced him around at Bulldog Raceway. He didn't embarrass me even once!  It was good seein' ya again Cookie!
|
|
| Author: | wvenable [ Mon Jul 08, 2013 5:46 am ] |
| Post subject: | |
Yep enjoyed myself. Brought down a hand held Garmin gps for Mater's son Mr. Mike - did I tell ya he is the brains of the outfit? Mr. Mike is going to have a few adventures geocaching. Got holt of a torque converter for the Demon - originally belonged to Possum - I miss his unique and cryptic posts. Picked up a few other bamboozler parts while horse tradin. Took the scenic route home and got to see the Fort Knox building where all of our gold is - yeah right - prolly all in China by now. Went past Ohio Valley Dragway and an interesting establishment called River Girls. I am thinking they must give boat tours or sumpin. Good way to spend the day - thanks Mater! |
|
| Author: | Rob Simmons [ Mon Jul 08, 2013 6:05 am ] |
| Post subject: | |
I told you to take that left at Albuquerque!! You missed that right at Joe Prather by about 30 miles... That scenic route is fun though. Thanks again for that GPS fer Mike! He signed up & we'll be snoopin' & poopin' around today. You wudn't s'posed ta tell 'bout dem udder Bamboozler parts!! Challenger content: I cut a piece of lexan and drilled a hole in it so I can cc some chambers. And I got the garage back to a usable state. I can even walk around both cars now!
|
|
| Author: | slantzilla [ Mon Jul 08, 2013 8:02 am ] |
| Post subject: | |
Boat tours. Useable garage.
|
|
| Author: | Rick Covalt [ Mon Jul 08, 2013 11:51 am ] |
| Post subject: | |
Quote: snoopin' & poopin'
That must be a Kentucky thing! We don't tell people about that up her in PA!! Rick |
|
| Author: | Rob Simmons [ Mon Jul 08, 2013 7:20 pm ] |
| Post subject: | |
Yeah,... well,... mebbe we share a little too much from time to time... Anywho... We found our first geocache today. There are like a dozen of these things within a few blocks of our house! We started lookin' fer the second one on our list, but had to quit and go to a swim meet and 4-H archery practice. We'll be findin' a bunch of these things... Yeah, yeah... Rob has yet another hobby to distract him... This one ain't got nuthin' to do with cars and is Mike's hobby, not mine! So there! No Challenger content in this post.
|
|
| Page 11 of 61 | All times are UTC-07:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|