| Slant Six Forum https://www.slantsix.org/forum/ |
|
| Shim head gaskets https://www.slantsix.org/forum/viewtopic.php?t=66308 |
Page 3 of 3 |
| Author: | Charrlie_S [ Mon Dec 13, 2021 7:15 am ] |
| Post subject: | Re: Shim head gaskets |
Got the gaskets on Friday. I have a problem with the composition gaskets. The "BIG BORE" gaskets that people wanted were Permaseal AP210. They had a bore size of 3.660 The gaskets I received are "ACL AP210". They have a bore size of 3.550. The shim gaskets have a bore size of 3.510 The problem with the Ap210 is my fault. I went by the part number and didn't inquire about the brand. Those of you that ordered the composition AP210 "big bore", let me know if you still want them, with the smaller bore size, or wish to cancel them. My error, so if you wish to cancel, that is my problem. I'll have to "eat it". Meanwhile I'll start packaging the shim gaskets for those that are just getting those. Give me a few days. |
|
| Author: | GTS225 [ Mon Dec 13, 2021 11:39 am ] |
| Post subject: | Re: Shim head gaskets |
Charlie; I'm good with the "small bore" gaskets. Thanks.....Roger |
|
| Author: | Rick Covalt [ Tue Dec 14, 2021 3:25 am ] |
| Post subject: | Re: Shim head gaskets |
Charlie, I really don't need the smaller bore size gaskets. I have plenty of them. See if someone else want or needs that size. Are you planning to reorder the big bore ones? If no one wants the ones that came in I'll keep them. I don't want you to eat them! I'm sure they aren't very tasty! 
|
|
| Author: | Charrlie_S [ Tue Dec 14, 2021 3:37 am ] |
| Post subject: | Re: Shim head gaskets |
Quote: Charlie, I really don't need the smaller bore size gaskets. I have plenty of them. See if someone else want or needs that size. Are you planning to reorder the big bore ones? If no one wants the ones that came in I'll keep them. I don't want you to eat them! I'm sure they aren't very tasty!
No problem. I'm going to check and see if the Permaseal gaskets are available.
|
|
| Author: | GTS225 [ Fri Dec 31, 2021 5:24 am ] |
| Post subject: | Re: Shim head gaskets |
Say, Charlie......have you sent anything out yet? Just checking, because if you have, I haven't recieved it yet. Roger |
|
| Author: | Charrlie_S [ Sat Jan 08, 2022 3:38 am ] |
| Post subject: | Re: Shim head gaskets |
I have been sending out the gaskets a little at a time. Please bare with me. I will send a PM with tracking number when each is shipped. I found some money in an envelope on my desk. If someone sent me cash, please let me know. I really don't know if it was for gaskets or something else. Don't know where it came from. |
|
| Author: | hyper_pak [ Tue Jan 18, 2022 5:20 pm ] |
| Post subject: | Re: Shim head gaskets |
Got my gaskets today Charlie. Thank you for the careful packing and extra effort. I know that was a lot of work and I appreciate it! |
|
| Author: | Charrlie_S [ Wed Jan 19, 2022 4:19 am ] |
| Post subject: | Re: Shim head gaskets |
All gaskets have been shipped. If anyone doesn't have theirs by Sat or monday, let me know. Or if packages are damaged. (Lou and Rick I'm holding yours for possible hand delivery) |
|
| Author: | Greg Ondayko [ Wed Jan 19, 2022 5:21 am ] |
| Post subject: | Re: Shim head gaskets |
Got mine.. Packaged with indestructo methods and materials. Thank you Charrile. Greg |
|
| Page 3 of 3 | All times are UTC-07:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|