Got the motor and transmission out, the K frame removed and the new one installed. Motor should be ready to set down in the car again in a few days!
| Slant Six Forum https://www.slantsix.org/forum/ |
|
| Covalt - "Project 65 Valiant" https://www.slantsix.org/forum/viewtopic.php?t=35632 |
Page 64 of 125 |
| Author: | Rick Covalt [ Tue Jan 31, 2017 6:45 pm ] |
| Post subject: | |
Got the motor and transmission out, the K frame removed and the new one installed. Motor should be ready to set down in the car again in a few days!
|
|
| Author: | slantzilla [ Tue Jan 31, 2017 7:55 pm ] |
| Post subject: | |
That shore be purty, Rick. 
|
|
| Author: | Rob Simmons [ Wed Feb 01, 2017 2:55 am ] |
| Post subject: | |
Coooool! 
|
|
| Author: | Dart270 [ Wed Feb 01, 2017 3:35 am ] |
| Post subject: | |
Nice work, Rick! Bet you can smell the 12s... Lou |
|
| Author: | wvenable [ Wed Feb 01, 2017 5:07 am ] |
| Post subject: | |
Yep, nicely done Mr. Covalt. |
|
| Author: | Ron Hamby [ Wed Feb 01, 2017 7:06 am ] |
| Post subject: | |
Really like that K frame. looks real good. |
|
| Author: | Rick Covalt [ Wed Feb 01, 2017 1:23 pm ] |
| Post subject: | |
Quote: Nice work, Rick! Bet you can smell the 12s...
Once the engine fires and has oil pressure, I'll start sniffing for the 12.99!
|
|
| Author: | Rick Covalt [ Wed Feb 01, 2017 3:10 pm ] |
| Post subject: | |
I removed the oil pump from the mild race engine that I pulled on Monday to check the oil pump and cam gears. I was excited to see two good gears after 3 seasons of racing. So once the race car is done I'll be doing another swap into my truck.
|
|
| Author: | Rick Covalt [ Thu Feb 02, 2017 6:14 pm ] |
| Post subject: | |
Looked at my Jeffrey head and the new intake/exhaust gasket and the intake ports are almost a perfect match as is. The intake runners are slightly smaller than the gasket so I am just leaving them as is. I lined up the manifold on the gasket and made a couple hash marks. Them I installed the gasket on the head with the intake to see how it lined up on the head. All appears to be fine!  I finished installing the Stage 8 fasteners on the oil pan so I dont have to worry about them coming loose. There is not enough in the kit to do the whole pan so I drilled the heads on some allen screws and used safety wire on the ends. I'm especially glad to know than none of them can fall out!. I've had that happen before and it makes a mess.    Rick |
|
| Author: | slantzilla [ Thu Feb 02, 2017 6:50 pm ] |
| Post subject: | |
Nice!
|
|
| Author: | drgonzo [ Fri Feb 03, 2017 5:23 am ] |
| Post subject: | |
Rick, what intake gasket is that? |
|
| Author: | Greg Ondayko [ Fri Feb 03, 2017 12:53 pm ] |
| Post subject: | |
Cox brothers reissue by brian droschak You can pm him here. User name: Brian Greg |
|
| Author: | Rick Covalt [ Sat Feb 04, 2017 1:04 pm ] |
| Post subject: | |
Next time you see this it will be in a car!! Couldn't decide if I wanted the intake blue or silver. Blue it is!  
|
|
| Author: | Romeo Furio [ Sat Feb 04, 2017 6:06 pm ] |
| Post subject: | |
Sure is nice looking 
|
|
| Author: | Dart270 [ Mon Feb 06, 2017 11:08 am ] |
| Post subject: | |
Um, wow. Lou |
|
| Page 64 of 125 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|