Slant Six Forum
https://www.slantsix.org/forum/

Another engine mount possibility - someone wanna try it?
https://www.slantsix.org/forum/viewtopic.php?t=13236		 Page 1 of 2
Author:  SlantSixDan [ Thu Jun 02, 2005 9:18 am ]
Post subject:  Another engine mount possibility - someone wanna try it?
NLM found this thread regarding installation of a 318 into a '65 A-body using '88 Toyota Supra engine mount insulators with '67-'72 A-body brackets.

Looks kind of interesting. The '88 Supra uses a 181 CID inline Six, normally aspirated or turbocharged, and the motor mount insulators look like this:

Image

Beck-Arnley 1041240 or Anchor 9034.

Dimensions of this insulator look like they might be a good "problem solver" candidate for early A-body cars, but without having the insulators in hand, it's difficult to tell.
Author:  NewLancerMan [ Thu Jun 02, 2005 9:53 am ]
Post subject: 
I'd be happy to give it a try, but I don't have the 67-up brackets. Anyoe have a sets they want to send me? The engine is out and ready ;-)

MJ
Author:  SlantSixDan [ Sun Jul 24, 2005 8:23 am ]
Post subject: 
I don't think the "67-up brackets" comment would apply to these mount biscuits' use in early slant-6 A-bodies; I'm guessing you could carry on using your existing brackets.
Author:  Charrlie_S [ Sun Jul 24, 2005 3:22 pm ]
Post subject: 
That mount will not work on a 63-66 slant passenger side, without mods. The stock insulator has two wide spaced studs that fasten to the engine bracket. It is possible it might work on the driver side.
Author:  SlantSixDan [ Sun Jul 24, 2005 5:36 pm ]
Post subject: 
The idea would be to use one of the two lower stud holes on the LH side.
Author:  argentina-slantsixer [ Sun Jul 24, 2005 7:57 pm ]
Post subject: 
we have biscuit type mounts readily avalible. I can send some to dan in small quantity and see if he's happy with the quality. Then will see how we can manage the shipping thingy.

do if you're to speak about this do so or remain silent forever. :wink:
Author:  voiceofstl [ Mon Jul 25, 2005 8:02 pm ]
Post subject:  call me dumb
Aren't after market motor mounts and brakets readly avable on the after market for these coversions? I mean people have been swapping a 318 into a /6 for decades.
Author:  voiceofstl [ Mon Jul 25, 2005 8:02 pm ]
Post subject:  call me dumb
Aren't after market motor mounts and brakets readly avable on the after market for these coversions? I mean people have been swapping a 318 into a /6 for decades.
Author:  Charrlie_S [ Tue Jul 26, 2005 4:51 am ]
Post subject: 
Quote:
The idea would be to use one of the two lower stud holes on the LH side.
Sorry, Dan. I misread the original post. I thought we were talking about replacement mounts for the 63-66 slant, not V-8 conversion mounts.
Author:  SlantSixDan [ Tue Jul 26, 2005 8:18 am ]
Post subject: 
Quote:
Quote:
The idea would be to use one of the two lower stud holes on the LH side.
Sorry, Dan. I misread the original post. I thought we were talking about replacement mounts for the 63-66 slant, not V-8 conversion mounts.
We are talking about replacement '62-'66 slant A-body mount insulators.
Author:  Charrlie_S [ Tue Jul 26, 2005 9:15 am ]
Post subject: 
Quote:
Quote:
Quote:
The idea would be to use one of the two lower stud holes on the LH side.
Sorry, Dan. I misread the original post. I thought we were talking about replacement mounts for the 63-66 slant, not V-8 conversion mounts.
We are talking about replacement '62-'66 slant A-body mount insulators.
Then I go back to my original statement. " I don't think it will work without mods". The left (driver) side maybe. The right (Pass) side, possibly weld a plate across the bottom of the bracket, and locate a hole in that for the insulator.

As a footnote: called my suppliers, and these mounts are "special order" not in stock, and sell for $50-$55 ea range.
Author:  SlantSixDan [ Tue Jul 26, 2005 1:56 pm ]
Post subject: 
H'm. Rockauto shows 'em in stock at around $40.
Author:  Charrlie_S [ Tue Jul 26, 2005 5:10 pm ]
Post subject: 
I called Rockauto today about the stock slant six insulators. Their online catalog, showed the later spool mount for the 62-66 slant. The telephone person, told me the correct mount is no longer available thru them. I then asked about the Anchor 9034, and was told not in stock, needed to be ordered. I was trying to see if I could get a pair cheaply to try. I have a 66 with the engine just sitting in there. Real easy to try them.
Author:  SlantSixDan [ Tue Jul 26, 2005 9:07 pm ]
Post subject: 
Pity Rockauto doesn't actually have 'em. www.partsamerica.com shows anchor 9034 as "Ships in 1 day", but their price isn't as friendly. On the other hand, they have a clearer photo of the part:

Image
Author:  Charrlie_S [ Thu Jul 28, 2005 8:51 am ]
Post subject: 
The Paddock shows the correct 62-66 slant six mounts on their website. I just ordered 2 of each at 17.95 ea. We'll see if they show up.
Page 1 of 2 All times are UTC-08:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/