Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Mon Dec 29, 2025 1:58 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 5 posts ] 
Author Message
 Post subject: 65 Cuda
PostPosted: Wed Apr 26, 2006 4:51 am 
Offline
2 BBL ''SuperSix''

Joined: Mon Mar 27, 2006 12:29 pm
Posts: 13
Car Model:
Just put the fresh 225 back in and fired her up - no oil. Replaced the oil pump during rebuild. Is there a way to prime the pump. The service manual does not cover this or do you think I :cry: :cry: got a bad one from NAPA
Thanks
Tom


Top
   
 Post subject:
PostPosted: Wed Apr 26, 2006 5:23 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8978
Location: Silver Springs, Fl.
Car Model:
First, do you have a guage? Are you sure you have no oil pressure, or just no oil to the valve train? If you don't have oil pressure, You should be able to remove the cover from the oil pump, and pack a small amount of vasoline in the gears. If you don't have oil to the valve train, there is a good chance the rear cam bearing is installed wrong, or a problem with the oil metering holes in the cam. Also silly question, you did install the oil pickup tube, didn't you? A crack in the pickup tube, could also cause no oil pressure.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Wed Apr 26, 2006 12:33 pm 
Offline
2 BBL ''SuperSix''

Joined: Mon Mar 27, 2006 12:29 pm
Posts: 13
Car Model:
Yea Carrlie got a guage no press took - oil filter off and started for 10-15 seconds - no oil. When I rebuilt the motor I didn't remove the pick-up. the oil press was good B4 I pulled the motor. I did pack the pump with grease berore installing. Do you think pulling a vacuum on the filter tube while turning it over will prime the pump?? This was a 5 bolt Melling pump - looked the same as the one I removed
Thanks
Tom


Top
   
 Post subject:
PostPosted: Wed Apr 26, 2006 8:35 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8978
Location: Silver Springs, Fl.
Car Model:
Oh, Oh. I was going to suggest a missing oil galley plug, but if there is no oil getting to the filter, that is not the problem. If you put grease in the pump, it should pump. Think you have a bad pump, or a problem with the pickup tube. Gear might be spinning on the pump shaft, or the pressure relief valve stuck open. I think, I would pull the cover off the pump and see if the rotors are turning, and remove the pressure relief valve cap and make sure there is a spring in there, and the valve moves freely. If it is easier, pull the pump and check it .

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Thu Apr 27, 2006 3:50 am 
Offline
2 BBL ''SuperSix''

Joined: Mon Mar 27, 2006 12:29 pm
Posts: 13
Car Model:
Thanks this w/e I'll give it a try
Tom


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 5 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: Google [Bot] and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited