Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Tue Nov 18, 2025 9:18 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 13 posts ] 
Author Message
 Post subject: 4 speed manual?
PostPosted: Mon Jan 14, 2008 5:01 pm 
Offline
1 BBL (New)

Joined: Mon Jan 14, 2008 3:55 pm
Posts: 7
Car Model:
I was just wondering if anyone out there knows where I can get a 4 speed trans for my '72 Demon. It's got a /6 225. I've tried junk yards but I've had no luck so far. Please any info will help a lot!


Top
   
 Post subject:
PostPosted: Mon Jan 14, 2008 5:51 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 24786
Location: North America
Car Model:
www.car-part.com , searchable used auto parts clear across North America. Put in 1976 Dodge Dart, transmission, search all areas, then on the next screen specify the last option ("M.T. 4-speed"). You'll get a lot of results. Then repeat the search with 1979 Dodge Aspen, and again pick the "4-speed" option on the second screen. You'll get even more results.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
PostPosted: Tue Jan 15, 2008 1:47 pm 
Offline
Turbo Slant 6

Joined: Tue Jun 14, 2005 8:29 pm
Posts: 797
Location: Raleigh, NC
Car Model:
I have a used, known good one and all the accessories like bell, fork, etc. Used in my '64D100 for bench mockups.

PM me if interested,
rock
'64d100


Top
   
 Post subject:
PostPosted: Tue Jan 15, 2008 2:09 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 24786
Location: North America
Car Model:
Careful there — car 4spd not the same as truck 4spd in the '60s.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
PostPosted: Wed Jan 16, 2008 6:34 am 
Offline
Turbo Slant 6

Joined: Tue Jun 14, 2005 8:29 pm
Posts: 797
Location: Raleigh, NC
Car Model:
Yeh,

Good advice to him Dan! Since I am so used to fitting stuff up I forget what I have to do at times to get stuff to work!

I have and finally used A833OD's from cars, with long tailshaft and 23 spline inputs, because I didn't want NP435's with that low low gear. Course doing so required a new crank, thus new engine, modifying one cross from which to take measurements.

If I had known more of what it would take before I got started, MAYBE I would have put in the 727 to start with....naaah, I wanted the 4 speed, then after having it wanted to try something else. Talk about "project creep"! But ya know, us slanters probably all like a challenge.

Still take Dan to heart, I am almost certain you wouldn't want the super heavy truck 4 speed, the NP435. Of course the guys who have done car conversions have posted periodically of the perils they encountered too, so I would caution you that what you want to do is not likely to be plug and play and not be done in one weekend.

rock
'64d100


Top
   
 Post subject:
PostPosted: Sat Jan 19, 2008 5:22 pm 
Offline
EFI Slant 6
User avatar

Joined: Sat Mar 12, 2005 9:33 am
Posts: 261
Location: Marquette, MI 49855 (Upper Peninsula)
Car Model:
I have an 70k mile original 3-speed from my parts 1972 Demon if you're interested. It can be had CHEAP!

_________________
1969-1/2 Dodge Super Bee A12 (440 Six Pack, 4-spd, Dana 60)
1974 Plymouth Duster 360 (4-spd, 8.75")
1973 Plymouth Duster (225, auto, 8.25")
2001 Dodge Ram 1500 QC 2wd (5.9L, auto, Dana 60)


Last edited by daniel_depetro on Mon Jan 28, 2008 2:39 pm, edited 1 time in total.

Top
   
 Post subject:
PostPosted: Sun Jan 20, 2008 4:59 pm 
Offline
4 BBL ''Hyper-Pak''
User avatar

Joined: Fri Nov 09, 2007 12:54 pm
Posts: 49
Location: centerport , ny
Car Model: 65 Valiant station wagon ,66 Valiant convertible,
I'd look for a 64-65 Valiant Barracuda Dart iron A833 and use that.It has the 309 first gear and 1to 1 4th and makes for a nice driving 6 .They are out there and so are the bellhousings for them I just bought one last month. It will be a basic bolt in job this way.


Top
   
 Post subject:
PostPosted: Mon Jan 28, 2008 1:25 pm 
Offline
3 Deuce Weber

Joined: Tue Dec 11, 2007 8:40 am
Posts: 94
Location: Orlando, FL
Car Model:
does the crank need to be modified to take the pilot bearing? or is it just a buy parts and swap type thing?


Top
   
 Post subject:
PostPosted: Mon Jan 28, 2008 1:46 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8968
Location: Silver Springs, Fl.
Car Model:
Quote:
I'd look for a 64-65 Valiant Barracuda Dart iron A833 and use that.It has the 309 first gear and 1to 1 4th and makes for a nice driving 6 .They are out there and so are the bellhousings for them I just bought one last month. It will be a basic bolt in job this way.
The 64-65 trans, has a flange on the rear of the trans, to accept the Ball and Trunion joint. Driveshaft mods would be required.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Mon Jan 28, 2008 2:17 pm 
Offline
Supercharged
User avatar

Joined: Wed Oct 12, 2005 9:00 pm
Posts: 3048
Location: kankakee IL
Car Model: 80 volare, 78 fury 2 dr, 85 D150
I believe from the other thread that camel wants the non O/D version.
I'd suggest swap meets or Ebay, though I don't know whether his beef is that he only has 3 gears or if its that the shifter is "on the tree".... he's new, maybe if thats the issue (he wasnt real clear ) a tranny hump and a 3 spd shifter and rods would solve his "beef" with his car?


Top
   
 Post subject: If so...
PostPosted: Mon Jan 28, 2008 7:38 pm 
Offline
Board Sponsor
User avatar

Joined: Tue Oct 29, 2002 8:27 pm
Posts: 9714
Location: Salem, OR
Car Model:
Quote:
he's new, maybe if thats the issue (he wasnt real clear ) a tranny hump and a 3 spd shifter and rods would solve his "beef" with his car?
If this is true, then I would heavily suggest the A-230 3 spd (has synchro 1st gear...inland short throw shifter...1971-1974 ish) as the tranny to look up, they are fairly cheap to get, and will bolt right up to his 3spd bellhousing, and then he'll need to install a hump and new carpet.

Good idea!

-D.idiot


Top
   
 Post subject:
PostPosted: Wed Jan 30, 2008 11:21 pm 
Offline
1 BBL (New)

Joined: Mon Jan 14, 2008 3:55 pm
Posts: 7
Car Model:
Hey guys thanks for all the info. But I wanted was a four speed not because the shifter is on the tree but because I want that one more gear and my tranny is leaking really bad right now and I thought to myself well this is the perfect time to get what I want out of her.


Top
   
 Post subject:
PostPosted: Sun Feb 03, 2008 8:53 am 
Offline
Turbo Slant 6

Joined: Wed Sep 13, 2006 7:41 am
Posts: 922
Location: Eureka
Car Model:
I have a 4speed out od a 65 Barracuda.....withe the ball and trunion tail shaft. It is for sale......and I have a 3 speed from my 67 Barracuda , it had a 273 in front of it. Email me if you want.
Andrew/Kidd

_________________
Wife's: 64 Valiant
My: 70 Road Runner, 67 Barracuda, AND the 62 Valiant drag car!!


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 13 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited