| Slant Six Forum https://www.slantsix.org/forum/ |
|
| O-rings https://www.slantsix.org/forum/viewtopic.php?t=2794 |
Page 1 of 1 |
| Author: | RJ [ Mon Oct 22, 2001 10:15 am ] |
| Post subject: | O-rings |
I need to replace the o-rings on my sparkplug tubes,where can I get them? thanks rj@flyingcamel.net |
|
| Author: | Mike Latvala [ Mon Oct 22, 2001 2:58 pm ] |
| Post subject: | Re: O-rings |
Quote:
: I need to replace the o-rings on my sparkplug : tubes,where can I get them? : thanks Try the local hardware store. They should have a large assortment of o-rings in the plumbing department. latvalam@msoe.edu |
|
| Author: | RJ [ Mon Oct 22, 2001 3:38 pm ] |
| Post subject: | Re: O-rings |
I wasn't sure if they would take the heat. rj@flyingcamel.net |
|
| Author: | Mike Latvala [ Mon Oct 22, 2001 4:48 pm ] |
| Post subject: | Re: O-rings |
Quote:
: I wasn't sure if they would take the heat.
I'm not sure what is different between various o-rings, but I have been using the o-rings from the hardware store on the exhaust pipe of my dirtbike, with good results. I think it's worth trying; the o-rings are pretty cheap (less than a buck a piece), so even if they don't hold up right, you won't be out much more than the time it takes to change them. Good luck! latvalam@msoe.edu |
|
| Author: | Craig [ Mon Oct 22, 2001 9:06 pm ] |
| Post subject: | Re: O-rings |
I have a few sets left over from engine overhaul gasket sets. I only have the newer heads that do not need them. If I can find them I can mail you a set for cheap. They have a square cross section, not round like you get at the hardware store. cfield@ll.net |
|
| Author: | Richard Moore [ Mon Oct 22, 2001 10:38 pm ] |
| Post subject: | Re: O-rings |
Quote:
: I need to replace the o-rings on my sparkplug : tubes,where can I get them? : thanks Hi, You can get the o rings which are the same as the ones used on Hemi rocker covers from buymopar.com look in restoration parts link. I think they are a standard mopar part number P1947708. Regards Richard richard.e.moore@paradise.net.nz |
|
| Author: | WhaleMstr [ Tue Oct 23, 2001 7:38 pm ] |
| Post subject: | Re: O-rings |
Hey RJ, I got mine through NAPA - they had them in back on the shelf even! As was posted before, they have a square cross section and worked perfectly for me. Also, they were only a couple of bucks. Good luck, Dan gramma@dm-tech.net |
|
| Author: | RJ [ Fri Oct 26, 2001 10:21 am ] |
| Post subject: | Re: O-rings |
Thanks to everyone for their help,found them at NAPA AUTO PARTS,part#B45384 cost $6bucks. RJ rj@flyingcamel.net |
|
| Author: | Chuck Rivers [ Fri Oct 26, 2001 2:50 pm ] |
| Post subject: | Re: O-rings |
Quote:
: I need to replace the o-rings on my sparkplug : tubes,where can I get them? : thanks FYI: When I had my shop years ago, we gave up on the stock o-rings because they harden so quickly. We found an o-ring from Motion Industries (#2-218) that is good to 257º. I never had any wear out. You can usually get o-rings from a bearing supply store. Chuck webmaster@omnipages.com |
|
| Page 1 of 1 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|