Of course. It's bluprinted to 54cc's. Sorry about the delay.
| Slant Six Forum https://www.slantsix.org/forum/ |
|
| Ported Slant head. https://www.slantsix.org/forum/viewtopic.php?t=49178 |
Page 1 of 1 |
| Author: | StrokerScamp [ Mon Jul 02, 2012 12:03 pm ] |
| Post subject: | Ported Slant head. |
My apologies. Since I do not come here often, I had neglected to post my ported slant head here. Here it is, for anyone interested. Here is my ported slant head done by Jerry Killian, owner of http://killiansportingservice.com/index.html right down the road from me in Warner Robins, Georgia. He is a very renowned porter in this area. I have the flow sheet, which I will post later when I get time. Before and after flow @ .450 lift (which is about where my cam will be after lash and crappy rocker ratio). As luck would have it, I cannot upload the pictures from here. I will load them when I get home tonight. |
|
| Author: | Rug_Trucker [ Wed Jul 04, 2012 7:05 pm ] |
| Post subject: | |
Did you CC it? |
|
| Author: | StrokerScamp [ Fri Jul 06, 2012 11:43 am ] |
| Post subject: | |
Of course. It's bluprinted to 54cc's. Sorry about the delay.
|
|
| Author: | Rug_Trucker [ Fri Jul 06, 2012 9:36 pm ] |
| Post subject: | |
Those are big CC's. |
|
| Author: | Dart270 [ Sat Jul 07, 2012 1:39 pm ] |
| Post subject: | |
Looks like nice work. Interested to see flow numbers, or at least numbers at 0.200" and 0.500". Lou |
|
| Author: | Rug_Trucker [ Sat Jul 07, 2012 3:03 pm ] |
| Post subject: | |
Quote: Looks like nice work. Interested to see flow numbers, or at least numbers at 0.200" and 0.500".
His numbers are over at FABO lots of pics.Lou http://www.forabodiesonly.com/mopar/sho ... p?t=182649 |
|
| Author: | Exner Geek [ Sat Jul 07, 2012 5:20 pm ] |
| Post subject: | |
What type and size of valves are you using? What stem diameter and type of guide? Looks like a nice head. |
|
| Author: | StrokerScamp [ Sun Jul 08, 2012 6:44 pm ] |
| Post subject: | |
Quote: Those are big CC's.
Blueprinted back to stock because I'm running the KB239s with 198 rods. It needs to be a pump gas motor.
|
|
| Author: | StrokerScamp [ Sun Jul 08, 2012 6:45 pm ] |
| Post subject: | |
Quote: What type and size of valves are you using? What stem diameter and type of guide? Looks like a nice head.
Stock 1.78 and 1.50 318 valves with 3/8 stems.
|
|
| Author: | StrokerScamp [ Sun Jul 08, 2012 6:46 pm ] |
| Post subject: | |
Quote: Quote: Looks like nice work. Interested to see flow numbers, or at least numbers at 0.200" and 0.500".
His numbers are over at FABO lots of pics.Lou http://www.forabodiesonly.com/mopar/sho ... p?t=182649 http://www.forabodiesonly.com/mopar/sho ... tcount=111 |
|
| Author: | Dart270 [ Sun Jul 08, 2012 7:45 pm ] |
| Post subject: | |
Nice numbers and no reversion at high lifts. Should be a fun motor. Lou |
|
| Author: | Rug_Trucker [ Sun Jul 08, 2012 8:47 pm ] |
| Post subject: | |
This site is pretty easy going. |
|
| Author: | StrokerScamp [ Mon Jul 09, 2012 5:39 am ] |
| Post subject: | |
Quote: This site is pretty easy going.
I'm glad. I was worried about posting a link. I would have just done that, but I wanted to add some here too since I don't post a lot here.
|
|
| Page 1 of 1 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|