Yepper. Dat's my car!
CJ
| Slant Six Forum https://www.slantsix.org/forum/ |
|
| Is this anybody "we" know? https://www.slantsix.org/forum/viewtopic.php?t=54935 |
Page 1 of 1 |
| Author: | GTS225 [ Sun Mar 23, 2014 4:53 am ] |
| Post subject: | Is this anybody "we" know? |
Ceej, is this for you? http://www.jalopyjournal.com/forum/show ... p?t=871056 Roger |
|
| Author: | ceej [ Sun Mar 23, 2014 9:14 am ] |
| Post subject: | |
Yepper. Dat's my car! CJ |
|
| Author: | Joshie225 [ Sun Mar 23, 2014 9:39 am ] |
| Post subject: | |
That looks great. Let me know when its home so I can see it in person if you would please. |
|
| Author: | DadTruck [ Sun Mar 23, 2014 11:04 am ] |
| Post subject: | |
 H  T
|
|
| Author: | ceej [ Sun Mar 23, 2014 11:06 am ] |
| Post subject: | |
You bet Josh! Was fighting with the PRNDL switch on Linda's pickup yesterday. Once that's done, I can dump the Alfa off and take the rolling garage up to Gary's. Looking forward to seeing you! CJ |
|
| Author: | GTS225 [ Sun Mar 23, 2014 5:16 pm ] |
| Post subject: | |
Quote: Yepper. Dat's my car!
****************************************** CJ SWEET! Looks like you're gonna start going fast, now!  Roger |
|
| Author: | slantzilla [ Sun Mar 23, 2014 11:27 pm ] |
| Post subject: | |
Is there enough car there to hold you Ceej? 
|
|
| Author: | Fopar [ Sun Mar 23, 2014 11:32 pm ] |
| Post subject: | |
Dennis, I have seen Ceej in the seat of that chassis and he does fit. Richard |
|
| Author: | ceej [ Mon Mar 24, 2014 7:38 am ] |
| Post subject: | |
The tubes all creak a bit, but it keeps my butt off the ground! CJ |
|
| Author: | slantzilla [ Mon Mar 24, 2014 7:48 am ] |
| Post subject: | |
Yeah, but there isn't a motor in it yet.
|
|
| Author: | 300fan [ Tue Apr 01, 2014 8:51 pm ] |
| Post subject: | |
Ceej, saw that over on the other site.Gonna be one bad lil' digger!! |
|
| Author: | ceej [ Wed Apr 09, 2014 9:37 pm ] |
| Post subject: | |
The parts roll in slowly..... Maybe I'll hear from Ken tomorrow. I need an engine with crank in, adapter, flex plate and starter to move forward at this point. I'll have all that for this weekend. We'll likely use my 198 crank for the 210 build, and work our way through this stage. Next step is intake and blower to get the schoze ordered. Then we deal with the drive. Once that's figured out, injection. At least one person has been bit by the Mag already. Don't grab it by the top and turn the gear. Not me by the way. I've been nipped by mags before. Not fun. It's capable of nipping you at slow turns with the Rare Earth Magnets that were installed. 5.9 A is no joke! Beyond that we have a long process of safety gear and tuning. The wheelie bar is included in the chassis build. I need to come up with a lot of stuff though. My budget is still holding, but based on the extras, such as the hand formed body on this car, it's a bit thinner than I'd hoped. My original estimate has needed a reset here and there, but Gary has been a prince. If he has something, he's been providing it at cost. He really has bought into this project! I've been updating my slixers thread. I don't post on the end of it. No need to bring it to the front. I edit the original post. That's how I roll. If you have comments, post them here. I'll keep updating the original post over there. CJ |
|
| Page 1 of 1 | All times are UTC-07:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|