Can't find a picture of it and where do you recommend one buy one? I just found one website for this manifold.
Or does anyone here have an extra one they would like to sell?

_________________
67Cuda,FAST EZEFI,340cu,CR=10.25,RollerCam&Rocker (XR268HR,#20-810-9)(#1622-16)(EddyRPM#60779,#7576), (MSD6AL,#6425) A904, GearVendorsOD, 8 1/4,3.55:1, ClassicAir

http://www.offyparts.com/

Specifically:

http://www.offyparts.com/product_info.p ... 6a509d4a70

The price is a bit steep at $320 for a new manifold. I would shop ebay, swap meets, and local classifieds before buying new. I picked up my offy intake never been installed for $60.

_________________
Casually looking for a Clifford hyperpak intake for cheap.

These go by fairly regularly on eBay...keep eyes open!

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

do I have the part number wrong? 5370? or 5270
for automatic Barracuda 5270A?
Ebay for sure just need to be sure what I am bidding on.
The Clifford one come with EFI bosses yes?
I plan someday to FI this engine, but I am looking for more low end torque which Offy should diliver.

_________________
67Cuda,FAST EZEFI,340cu,CR=10.25,RollerCam&Rocker (XR268HR,#20-810-9)(#1622-16)(EddyRPM#60779,#7576), (MSD6AL,#6425) A904, GearVendorsOD, 8 1/4,3.55:1, ClassicAir

P/N is 5270. Searching by P/N on eBay won't get you very far...?

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

I am unclear about a couple of things.
Quoted "Intake manifold heat helps fuel milage and cold engine operation.
No heat on the intake helps you get max power. If it is a street car that you drive a lot and you have the Offy intake, I would use the intake heat feature. (keep the heat riser valve operational)"

I plan on using the Durta Duals. (rear manifold just cut and sealed off)
The factory setup has the exhaust and the intake gasketed and bolts to one other just below the carb. Does the Offenhauser set up this way? Can they be bolted to each other? If not wouldn't the exhaust leak at this point? Doesn't the Offenhauser intake have a coolant circuit for this adding of heat?
I would think that sealing off the front branch and the heat riser would be the correct way.

_________________
67Cuda,FAST EZEFI,340cu,CR=10.25,RollerCam&Rocker (XR268HR,#20-810-9)(#1622-16)(EddyRPM#60779,#7576), (MSD6AL,#6425) A904, GearVendorsOD, 8 1/4,3.55:1, ClassicAir

That is very good advice.
Another good idea!
Yes.
No.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

If you are buying used make sure it comes with the adapter for the current Holley / AFB base. I see alot of them for sale without it. It will be one less thing to mess with.

More clearity needed. Are all 5270 manifolds the same? I plan to bolt on a Holley 4 barrel. Do I need an adapter plate? My 904 is rod connected. Do I need this kit? Linkage Kit: Barracuda Quad Manifold w/ Automatic Trans (5270A)
[OFFY-5270-A] $93.84
Linkage Kit for Barracuda Quad Manifold with Cable Operated carb and Automatic Trans

_________________
67Cuda,FAST EZEFI,340cu,CR=10.25,RollerCam&Rocker (XR268HR,#20-810-9)(#1622-16)(EddyRPM#60779,#7576), (MSD6AL,#6425) A904, GearVendorsOD, 8 1/4,3.55:1, ClassicAir

Here you go.



http://www.merchantamerica.com/chevyhot ... duct=75240


You may want to call them if you buy to see what it comes with & needs


They also have that Kick down linkage kit for $70.00



Jess

I still have the Offie manifold, and also a Dutra dual exhaust manifold. Also just got a brand new linkage set, yesterday.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225

You mean for sale, Charlie? I'd be interested on the 4 bl mani

_________________
Juan Ignacio Caino

Please use e-mail button istead of PM'ing. I do log in sometimes but I'll be answering quicker thru e-mail.

Yes, intake manifold only, used, very good condition with the carb plate. $150 plus shipping. I have never shipped anything out of the US, so I will have to see what is involved.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225

Oh man! I've been looking for a used one of those forever! I'll take it if you're willing to ship to argentina. I'll send you a PM

_________________
Juan Ignacio Caino

Please use e-mail button istead of PM'ing. I do log in sometimes but I'll be answering quicker thru e-mail.

BrenCuda,

With my Dutras and Offy intake I have used both spreadbore and squarebore 4bbls..it just takes adapters. In some previous posts Reed, I believe, suggested I try a 2" high spacer. I did. It's great. I am gonna add on another inch one day soon just to see what 3 inches does, but 2 is better than one is better than a mere plate adapter. More pull in lower gears and rpms.

The Offy is often used on Jeeps too, so look on ebay for Offenhauser manifold, jeep intake, etc. Usually run $150 to $250 depending on particular sale and goodies that come with the manifold.

rock
'64d100